Subject:
Re: Plustek OpticPro P12 and Red Hat 8
From:
Mikael Kujanpaa ####@####.####
Date:
26 Oct 2002 20:24:19 -0000
Message-Id: <200210262306.32526.mahead80@nic.fi>
Viestissä Lauantai 26. Lokakuuta 2002 16:22, Jaeger, Gerhard kirjoitti:
> You might enable the debug messages of the driver
> (recompile with option DEBUG=y --> make all DEBUG=y)
> then reinstall and make load.
> Send us the output of dmesg to see where the problem is.
> If even Windoze does not find it, I suspect, that the scanner is dead...
I'm not sure, if I understood correctly what you want (I'm newbie with
Linux), but I made full re-install. After that, I wrote "dmesg" as a root.
I get this:
(if that wasn't what you meant, please give me dummy-instructions ;) )
[root@val143 plustek_driver]# dmesg
Linux version 2.4.18-17.8.0 ####@####.#### (gcc version
3.2 20020903 (Red Hat Linux 8.0 3.2-7)) #1 Tue Oct 8 13:51:08 EDT 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
255MB LOWMEM available.
On node 0 totalpages: 65520
zone(0): 4096 pages.
zone(1): 61424 pages.
zone(2): 0 pages.
Kernel command line: ro root=LABEL=/ hdc=ide-scsi
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 504.003 MHz processor.
Speakup v-1.00 CVS: Tue Jun 11 14:22:53 EDT 2002 : initialized
Console: colour VGA+ 80x25
Calibrating delay loop... 1003.71 BogoMIPS
Memory: 253060k/262080k available (1313k kernel code, 6588k reserved, 989k
data, 172k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 4096 (order: 3, 32768 bytes)
ramfs: mounted with options: <defaults>
ramfs: max_pages=31888 max_file_pages=0 max_inodes=0 max_dentries=31888
Buffer cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 0387f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0387f9ff 00000000 00000000 00000000
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Pentium III (Katmai) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ####@####.####
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfafe0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/7110] at 00:07.0
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: Card 'NE2000 PLUG & PLAY ETHERNET CARD'
isapnp: 1 Plug & Play card detected total
speakup: initialized device: /dev/synth, node (MAJOR 10, MINOR 25)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 480 slots per queue, batch=120
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: QUANTUM FIREBALLlct10 15, ATA DISK drive
hdb: ST34321A, ATA DISK drive
hdc: HL-DT-ST GCE-8320B, ATAPI CD/DVD-ROM drive
hdd: ATAPI CDROM, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c03afd84, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03afd84, I/O limit 4095Mb (mask 0xffffffff)
hda: 29336832 sectors (15020 MB) w/418KiB Cache, CHS=1826/255/63, UDMA(33)
blk: queue c03afec0, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03afec0, I/O limit 4095Mb (mask 0xffffffff)
hdb: 8404830 sectors (4303 MB) w/128KiB Cache, CHS=523/255/63, UDMA(33)
ide-floppy driver 0.99.newide
Partition check:
hda: hda1 hda2 hda3
hdb: hdb1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 129k freed
VFS: Mounted root (ext2 filesystem).
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 172k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 13:57:43 Oct 8 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 7 for device 00:07.2
PCI: Sharing IRQ 7 with 00:0b.0
PCI: Sharing IRQ 7 with 00:0b.1
usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 7
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik ####@####.####
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
hub.c: USB new device connect on bus1/2, assigned device number 2
usb.c: USB device 2 (vend/prod 0x3f0/0x317) is not claimed by any active
driver.
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,2), internal journal
Adding Swap: 522104k swap-space (priority -1)
usb.c: registered new driver usblp
printer.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid
0x03F0 pid 0x0317
printer.c: v0.11: USB Printer Device Class driver
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.18, 14 May 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hdd: ATAPI 48X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: CD-RW GCE-8320B Rev: 1.04
Type: CD-ROM ANSI SCSI revision: 02
parport0: PC-style at 0x278 [PCSPP,TRISTATE,EPP]
ohci1394: pci_module_init failed
ip_tables: (C) 2000-2002 Netfilter core team
8139too Fast Ethernet driver 0.9.25
PCI: Found IRQ 9 for device 00:0a.0
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 Fast Ethernet at 0xd08f2000, 00:50:fc:5a:80:f2, IRQ 9
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
nvidia: loading NVIDIA Linux x86 NVdriver Kernel Module 1.0-3123 Tue Aug
27 15:56:48 PDT 2002
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: Detected Intel 440BX chipset
agpgart: AGP aperture is 64M @ 0xe0000000
NVRM: AGPGART: Intel 440BX chipset
NVRM: AGPGART: aperture: 64M @ 0xe0000000
NVRM: AGPGART: aperture mapped from 0xe0000000 to 0xd1a85000
NVRM: AGPGART: mode 2x
NVRM: AGPGART: allocated 16 pages
es1371: version v0.30 time 13:58:54 Oct 8 2002
PCI: Found IRQ 9 for device 00:09.0
es1371: found chip, vendor id 0x1274 device id 0x1371 revision 0x06
es1371: found es1371 rev 6 at io 0xe400 irq 9
es1371: features: joystick 0x0
ac97_codec: AC97 Audio codec, id: 0x4352:0x5913 (Cirrus Logic CS4297A rev
A)
parport0: PC-style at 0x278 [PCSPP,TRISTATE,EPP]
pt_drv : driver version 0.42-10
pt_drv : no device(s) detected, (-9023)
pt_drv : driver version 0.42-10
pt_drv : no device(s) detected, (-9023)
pt_drv : driver version 0.42-10
pt_drv : no device(s) detected, (-9020)
pt_drv : driver version 0.42-10
pt_drv : no device(s) detected, (-9023)
pt_drv : driver version 0.42-10
pt_drv : no device(s) detected, (-9020)
pt_drv : driver version 0.42-10
pt_drv : no device(s) detected, (-9020)
pt_drv : driver version 0.42-10
pt_drv : no device(s) detected, (-9020)
pt_drv : driver version 0.42-10
pt_drv : no device(s) detected, (-9020)
usb.c: USB disconnect on device 2
printer.c: usblp0: removed
hub.c: USB new device connect on bus1/2, assigned device number 3
printer.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 1 proto 2 vid
0x03F0 pid 0x0317
NVRM: AGPGART: freed 16 pages
NVRM: AGPGART: backend released
NVRM: AGPGART: Intel 440BX chipset
NVRM: AGPGART: aperture: 64M @ 0xe0000000
NVRM: AGPGART: aperture mapped from 0xe0000000 to 0xd1a85000
NVRM: AGPGART: mode 2x
NVRM: AGPGART: allocated 16 pages
NVRM: AGPGART: freed 16 pages
NVRM: AGPGART: backend released
NVRM: AGPGART: Intel 440BX chipset
NVRM: AGPGART: aperture: 64M @ 0xe0000000
NVRM: AGPGART: aperture mapped from 0xe0000000 to 0xd1a85000
NVRM: AGPGART: mode 2x
NVRM: AGPGART: allocated 16 pages
*********************************************
pt_drv: init_module()
pt_drv : driver version 0.42-10
ProcFsInitialize()
ptdrvInit(0)
Init settings done
ScanData = 0xc9f84000
Using fast I/O
Requested port at 0x278
Requested port (0x278) found
Port mode reported: (0x0047)
Port for device 0 registered
ptdrvOpen(port=0x278)
Try to claim the parport
parport-modi: SPP PS/2 EPP EPP(ECP) PS/2(ECP)
Use of EPP-mode enforced
Starting Scanner-Autodetection
************ DETECTP48xx ************
ModelSet4800()
modelInitPageSettings()
A4 set
ModelSet4800() done.
P48xxInitAsic()
DacInitialize()
ImageInitialize()
IOFuncInitialize()
IOInitialize()
MotorInitialize()
Dataport = 0x0278
Ctrlport = 0x027a
Test 0x55
Test 0xAA
Compare data=0x7e and status=0x5e, port=0x278
p48xxReadWriteTest()
Can't find your model, asic = 0x5a
detectScannerConnection() returns -9031.
************* ASIC9800x *************
IOInitialize()
ASIC = 0x83
IOInitialize()
************* ASIC98003 *************
ModelSetP12()
ModelSet9360()
modelInitPageSettings()
A4 set
ModelSet9630() done.
modelInitPageSettings()
A4 set
ModelSetP12() done.
P12InitAsic()
DacInitialize()
ImageInitialize()
IOFuncInitialize()
IOInitialize()
MotorInitialize()
PCB-ID=0x10, CCD-ID=0x00
We have a Plustek Scanner
P12InitAsic() done.
Dataport = 0x0278
Ctrlport = 0x027a
Test 0x55
Test 0xAA
Compare data=0x7e and status=0x3e, port=0x278
ioP98ReadWriteTest()
Error in memory test at pos 8 (8 != 9)
ioP98ReadWriteTest()
detectScannerConnection() returns 0.
p12SetupScannerVariables()
p12InitP98003(0)
PCB-ID=0x10, CCD-ID=0x00, DAC-TYPE=0x05
We have a Plustek Scanner
SAMSUNG 8531
CCD-3797
*** setupBuffers ***
Driverbuf(132000 bytes) needed !
pColorRunTab = 0xd1cdd52c - 0xd1cd93a0
Adjust for 98003 ASIC
*** DETECTION DONE, result: 0 ***
Switching lamp 0 on.
ptdrvClose()
*** cleanup buffers ***
MiscRestorePort()
- no need to restore portmode !
Releasing parport
MiscGetModelName - id = 17
pt_drv0: P12 found on port 0x0278
pt_drv0: Lamp-Timer set to 180 seconds.
pt_drv0: WarmUp period set to 15 seconds.
pt_drv0: Lamp untouched on driver unload.
Lamp-Timer started!
pt_drv : init done, 1 device(s) found
---------------------------------------------
!! IRQ !! Lamp-Timer stopped.
Try to claim the parport
Releasing parport
[root@val143 plustek_driver]#
--
Mikki
