plustek: OpticPro 9630P
Subject:
Re: OpticPro 9630P
From:
"Jaeger, Gerhard" ####@####.####
Date:
13 Dec 2000 08:06:17 -0000
Message-Id: <00121309111701.00492@gja>
Hi Erasmo,
first of all, the tool find-scanner will not work with parallel-port
scanners! This is a rather old tool designed for SCSI-scanners.
Please have a look at the FAQ that was shipped with the driver -
there's one topic that deals with the "no devices" problem.
If this doesn't help, enable the debug messages of sane for
the plustek backend:
export SANE_DEBUG_PLUSTEK=12
The check what
scanimage -L
says....
Did you compile sane after installing the driver-code?
If not, you might get an error -9019 (in the debug output).
There's one thing that worries me, you say that you have an
OP9630P but the driver only recognizes an OP4830. Please
also enable the debug messages of the driver (see the
Makefile in plustek_driver), recompile and reload the module
and send the output of dmesg...
Gerhard
On Mit, 13 Dez 2000, erasmo perez wrote:
> hello dear list users :-)
>
> i have a little problem, and i hope i could find some answers is this
> list, thank you for your attention
>
> i have a flat bed scanner, whose model is OpticPro 9630P, which
> connects to the PC using the parallel port, without SCCI interface
>
> the cdrom of instalation has the url of www.obmlink.com (our bussines
> machines inc.), but i guess the hardware is made by plustek, at least
> plustek has a model called identically: OpticPro 9630P
>
> i have installed sane-1.0.3 (source) and the plustek_driver
>
> with lsmod i get:
>
> uxmal:~# lsmod
> Module Size Used by
> sd_mod 16092 0 (unused)
> ide-scsi 7412 0
> ppscsi 11228 0 (unused)
> sg 12160 0 (unused)
> scsi_mod 52048 3 [sd_mod ide-scsi ppscsi sg]
> pt_drv 74928 0 (unused)
> sb 34740 0 (unused)
> uart401 6352 0 [sb]
> sound 58284 0 [sb uart401]
> es1371 24608 0
> soundcore 2788 10 [sb sound es1371]
> loop 7872 0 (unused)
>
>
> and with:
>
> $ ls -l /proc/scsi
> total 0
> dr-xr-xr-x 2 root root 0 Dec 12 07:13 ide-scsi
> -rw-r--r-- 1 root root 0 Dec 12 07:13 scsi
>
>
> with dmesg i get:
>
> $ dmesg
> ...
> ppt_drv : driver version 0.37-21
> pt_drv0: 4830P found on port 0x0378
> pt_drv0: Lamp-Timer set to 60 seconds.
> pt_drv0: WarmUp period set to 15 seconds.
> pt_drv0: Lamp untouched on driver unload.
> ppSCSI 0.92 (0.92) installed
> scsi0 : SCSI host adapter emulation for IDE ATAPI devices
> scsi : 1 host.
>
> and in my /etc/modules.conf i get
>
> $ cat /etc/modules.conf
> ...
> aalias char-major-40 pt_drv
> post-install pt_drv modprobe -k parport
> options pt_drv lampoff=60 warmup=15 port=0x378 lOffonEnd=0 mov=0
>
> when the pc starts (at booting) the scanner turns on the tube lamp, as
> indicated by the options of /etc/modules.conf, up to this point there
> seems to be no problem
>
>
> but when i try to scan i get:
>
> $ scanimage
> scanimage: no SANE devices found
>
> $ scanimage --listdevices
> scanimage: no SANE devices found
>
> tools# find-scanner
>
> # If your scanner uses SCSI, you must have a driver for your SCSI
> # adaptor and support for SCSI Generic (sg) in your Operating System
> # in order for the scanner to be used with SANE. If your scanner is
> # NOT listed above, check that you have installed the drivers.
>
>
> where could remain the problem ?
>
> thanks a lot for any help
>
> greetings
>
> erasmo
>
> pd. the parallel port is already stated as EPP
