plustek: plustek-driver/Suse 7.1/Kernel 2.4.
Subject:
Re: plustek-driver/Suse 7.1/Kernel 2.4.
From:
Poldi Winkler ####@####.####
Date:
14 Mar 2001 12:37:23 -0000
Message-Id: <01031413390300.00827@poldi>
Hello,
I have installed the plustek-driver 0.37.23 on the SuSE 7.1 and
sane 1.0.4 as rpm. The plustek-module.tar.gz I have copied to
/usr/share/doc/packages/sane and then installed. It was running at
once (as usual).
Rgds Poldi
Am Mittwoch, 14. März 2001 11:53 schrieben g.jaeger:
> Hi Thomas,
>
> in general, it should be possible to download a
> plustek-module... tar-ball, unpack it anywhere and build
> the driver. Please have a look at my homepage where you find
> which version is suitable for SANE-1.0.4.
> If you need the SANE sources, install the sane-... source-rpm
> from the SuSE-disk 6 or 7. The sources then can be found
> in /usr/src/packages...
>
> I recently did the same with SuSE 7.1 and a binary version
> of SANE 1.0.4 and this works without any problems
> (I must admit, that I use the latest development release
> of the driver which is not available to the public...)
>
> Gerhard
>
> P.S.: There's a german installation guide in each tar-ball,
> look for INSTALL.GER
>
> >----- Ursprüngliche Nachricht -----
> >Absender: ####@####.####
> >Betreff: plustek-driver/Suse 7.1/Kernel 2.4.
> >Empfänger: ####@####.####
> >Datum: 12. Mär 2001 21:11
> >
> > Hi,
> >
> > Firts: Thanks a lot for your providing a plustek-driver for
> > Linux.
>
> In
>
> > combination with sane 1.03, suse 7.0 and kernel 2.2 my scanner
> > OP
>
> 9630
>
> > worked fine. Great pleasure .-))
> >
> > But now ...
> >
> > I recently updated from 7.0 to 7.1 installing the new kernel
> > 2.4. I tried to make my scanner run, but I failed.
> >
> > Suse provides a special sane 1.04 installation with no
> > "backend" and
>
> all
>
> > the other stuff you get from the sane homepage with the
>
> sane-tarball.
>
> > However, www.mostang.com has been not reachable for the last
> > three
>
> days.
>
> > I couldn't get sane 1.04 yet, and I need some scans very
> > urgently.
> >
> > Question: is it possible to compile and install the
> > plustek-driver
>
> with
>
> > suse-sane and kernel 2.4? Is there any driver? Where should I
> > untar
>
> the
>
> > driver? What I have to do??? I had a glance at the RFMs, but I
> > understood nothing :-(
> >
> > Could you help me?
> >
> > Regards
> > Thomas Mandl
>
> -----------------------------------------------------------------
>----
>
> > To unsubscribe, e-mail: ####@####.####
> > For additional commands, e-mail: ####@####.####
>
> -----------------------------------------------------------------
>---- To unsubscribe, e-mail: ####@####.####
> For additional commands, e-mail: ####@####.####
